Cfg file illegal name?

AutomationDept

I try to load new parameters into my robotstudio virtual controller but every time it says that there is a configuration error and has an illegal name. This is the file that i am trying to load onto my virtual controller.

EIO:CFG_1.0:6:1::

#

DEVICENET_DEVICE:

      -Name "D652_10" \

      -RecoveryTime 5000 \

      -Address 10 \

      -Network "DeviceNet" \

      -VendorName "ABB Robotics" \

      -ProductName "24 VDC Unit" \

      -VendorId 75 \

      -ProductCode 26 \

      -DeviceType 7 \

      -ProductionInhibitTime 10 \

      -ConnectionType COS \

      -PollRate 1000 \

      -OutputSize 2 \

      -InputSize 2

EIO_SIGNAL:

      -Name "D652_10_DI1" -SignalType "DI" -Device "D652_10" -DeviceMap "0"

      -Name "D652_10_DI2" -SignalType "DI" -Device "D652_10" -DeviceMap "1"

      -Name "D652_10_DI3" -SignalType "DI" -Device "D652_10" -DeviceMap "2"

      -Name "D652_10_DI4" -SignalType "DI" -Device "D652_10" -DeviceMap "3"

      -Name "D652_10_DI5" -SignalType "DI" -Device "D652_10" -DeviceMap "4"

      -Name "D652_10_DI6" -SignalType "DI" -Device "D652_10" -DeviceMap "5"

      -Name "D652_10_DI7" -SignalType "DI" -Device "D652_10" -DeviceMap "6"

      -Name "D652_10_DI8" -SignalType "DI" -Device "D652_10" -DeviceMap "7"

      -Name "D652_10_DI9" -SignalType "DI" -Device "D652_10" -DeviceMap "8"

      -Name "D652_10_DI10" -SignalType "DI" -Device "D652_10" -DeviceMap "9"

      -Name "D652_10_DI11" -SignalType "DI" -Device "D652_10" -DeviceMap "10"

      -Name "D652_10_DI12" -SignalType "DI" -Device "D652_10" -DeviceMap "11"

      -Name "D652_10_DI13" -SignalType "DI" -Device "D652_10" -DeviceMap "12"

      -Name "D652_10_DI14" -SignalType "DI" -Device "D652_10" -DeviceMap "13"

      -Name "D652_10_DI15" -SignalType "DI" -Device "D652_10" -DeviceMap "14"

      -Name "D652_10_DI16" -SignalType "DI" -Device "D652_10" -DeviceMap "15"

      -Name "D652_10_DO1" -SignalType "DO" -Device "D652_10" -DeviceMap "0"

      -Name "D652_10_DO2" -SignalType "DO" -Device "D652_10" -DeviceMap "1"

      -Name "D652_10_DO3" -SignalType "DO" -Device "D652_10" -DeviceMap "2"

      -Name "D652_10_DO4" -SignalType "DO" -Device "D652_10" -DeviceMap "3"

      -Name "D652_10_DO5" -SignalType "DO" -Device "D652_10" -DeviceMap "4"

      -Name "D652_10_DO6" -SignalType "DO" -Device "D652_10" -DeviceMap "5"

      -Name "D652_10_DO7" -SignalType "DO" -Device "D652_10" -DeviceMap "6"

      -Name "D652_10_DO8" -SignalType "DO" -Device "D652_10" -DeviceMap "7"

      -Name "D652_10_DO9" -SignalType "DO" -Device "D652_10" -DeviceMap "8"

      -Name "D652_10_DO10" -SignalType "DO" -Device "D652_10" -DeviceMap "9"

      -Name "D652_10_DO11" -SignalType "DO" -Device "D652_10" -DeviceMap "10"

      -Name "D652_10_DO12" -SignalType "DO" -Device "D652_10" -DeviceMap "11"

      -Name "D652_10_DO13" -SignalType "DO" -Device "D652_10" -DeviceMap "12"

      -Name "D652_10_DO14" -SignalType "DO" -Device "D652_10" -DeviceMap "13"

      -Name "D652_10_DO15" -SignalType "DO" -Device "D652_10" -DeviceMap "14"

      -Name "D652_10_DO16" -SignalType "DO" -Device "D652_10" -DeviceMap "15"

#

It was working fine on my other desktop, but now that i have transferred the file to my new desktop the file wont load. If anyone can give some feedback it would be very much appreciated.

Pavel Riabichev

Hello
The error messages usally say at which line the name is illigal. Did your error message say that?
/Pavel

Johannes Weiman

When I copy the text to a file there are NBSP characters in the whitespace. Make sure the file is well formatted (for example by opening it in RS file editor and replacing all whitespace).

Regards,
Johannes